The ENTES SSRC-04 level relay (Empero code JP.M.ELK-KNT-ROL-025) monitors the water level in Empero and Ozti gas and electric boiling pans. Using electrodes, the relay senses the water in the double jacket of the boiling pan and allows heating only when the water is at the correct level. Without a working level relay, the boiling pan no longer starts or, worse, may heat without water, damaging the jacket, the burner or the heating elements.
Protection against running without water
The SSRC-04 is an electronic relay for conductive liquids, supplied at 190-260 V AC, 50/60 Hz. The electrodes in the boiling pan connect to terminals U (upper electrode), L (lower electrode) and B (reference electrode). When the water reaches the upper electrode, the relay changes state; when the level drops below the lower electrode, the relay releases and stops the heating. The sensitivity is set with the front potentiometer between 5 and 50 kOhm, according to the conductivity of the water, and the ON and OUT LEDs show the power supply and the output state. The changeover contact (C, NO, NC) is rated 8 A / 2000 VA.
Why choose this original relay?
Unlike generic relays, the ENTES SSRC-04 is exactly the relay used by Empero, with the same terminals, the same wiring diagram and the same DIN rail mounting, which makes it suitable for:
Empero and Ozti gas boiling pans: allows the burner to light only when the jacket is filled with water.
Electric boiling pans: locks out the heating elements when the water level drops.
Tanks and steam generators in HoReCa equipment: automatic level control for conductive liquids.
Service and maintenance: direct replacement, with the same wiring diagram.
Technical and Functional Advantages:
Adjustable sensitivity 5-50 kOhm: adapts to hard or soft water.
8 A / 2000 VA changeover output: directly controls the solenoid valve, the contactor or the burner control.
190-260 V AC, 50/60 Hz supply: works reliably even with mains voltage variations.
ON and OUT LEDs: quick diagnosis without measuring instruments.
Modular DIN rail format: 3.5 cm wide, quick mounting in the panel of the boiling pan.
Specifications at a glance:
Product type: Level relay / liquid level control relay
Empero code: JP.M.ELK-KNT-ROL-025
Part code: ENTES SSRC-04
Compatible with: Empero and Ozti / Oztiryakiler gas and electric boiling pans; the SSRC-04 model is printed on the front of the relay
Supply voltage: 190-260 V AC, 50/60 Hz
Output: 1 changeover contact, 8 A / 2000 VA
Sensitivity: 5-50 kOhm, adjustable
Easy to use
Before ordering, check the model on the front of the old relay (SSRC-04) and the Empero code. Disconnect the boiling pan from the power supply and, on gas models, close the gas valve. Note the wires on the terminals (U, L, B, NC at the top and A1, A2, C, NO at the bottom), remove the relay from the DIN rail and connect the new relay in the same order. Fitting must be carried out by an authorised technician; after fitting, fill the jacket with water, adjust the sensitivity if needed and check that the OUT LED lights up at the correct level. The relay measures 3.5 x 9 x 5.8 cm (width x height x depth).
Easy to clean
The relay is maintenance-free. Keep the panel of the boiling pan dry and clean. Regularly descale the electrodes in the jacket, because deposits change the level signal; use a soft cloth or a fine brush, without aggressive chemicals, only with the boiling pan switched off and cooled down.
Features and advantages of the ENTES SSRC-04 level relay
✓ The relay used by Empero in boiling pans, code JP.M.ELK-KNT-ROL-025
✓ Protects the boiling pan against running without water
✓ Adjustable sensitivity 5-50 kOhm
✓ 8 A / 2000 VA changeover output
✓ 190-260 V AC, 50/60 Hz supply
✓ DIN rail mounting, screw terminals