The M.ELK-EDM-JKT-016 thermocouple is the original temperature probe of the digital thermostat in Empero EMP.4G, EMP.6G, EMP.9G gas pizza ovens and in the double-deck versions EMP.4+4G, EMP.6+6G, EMP.9+9G. It is made by ORDEL (code OM-9/00003), has a type J (iron-constantan) element and a 2 m cable. When the probe fails, the thermostat shows a wrong temperature or an error, and the oven no longer holds the baking temperature.
Accurate measurement of the baking temperature
The type J thermocouple converts the heat in the baking chamber into an electrical signal that the digital thermostat reads continuously. The sensing element is protected by a rigid stainless steel sheath with a threaded fitting for fixing in the oven wall. Where it leaves the sheath, the cable has a 90° bend and a protective spring that prevents the wires from breaking, and along its full 2 m length it is protected by a metal braid. The wire ends are crimped, ready to connect to the thermostat.
Why choose this original thermocouple?
Unlike generic probes, this thermocouple has exactly the element type (J), cable length and fitting required by the Empero digital thermostat, which makes it suitable for:
Single-deck Empero gas pizza ovens (EMP.4G, EMP.6G, EMP.9G): correct temperature reading without recalibration.
Double-deck ovens (EMP.4+4G, EMP.6+6G, EMP.9+9G): one probe for each chamber.
High-output pizzerias: stable temperature, even baking from the first to the last pizza.
Service: direct replacement, with the same cable length and the same fitting.
Technical and Functional Advantages:
Type J element (Fe-Const): stable signal, suited to the digital thermostat of the oven.
Stainless steel sheath: withstands heat and the cleaning of the chamber.
2 m metal braided cable: protected against temperature and abrasion.
Protective spring at the bend: the wires do not break during fitting or from vibration.
Threaded fitting: secure fixing in the same position as the original probe.
Specifications at a glance:
Product type: Type J thermocouple / temperature probe
Empero code: M.ELK-EDM-JKT-016
Part code: ORDEL OM-9/00003 2MT J
Compatible with: Empero gas pizza ovens EMP.4G, EMP.6G, EMP.9G, EMP.4+4G, EMP.6+6G, EMP.9+9G
Element: 1 x Fe-Const (type J)
Cable length: 2 m
Easy to use
Before ordering, check the oven model and the label on the cable of the old probe (ORDEL, type OM-9/00003, Fe-Const element). Switch the oven off, close the gas, disconnect the power supply and wait until it has cooled down completely. Unscrew the fitting, remove the old probe and disconnect the wires from the thermostat, observing the polarity (plus and minus). Fit the new probe in the same seat, without sharply bending the sheath or the cable. Fitting must be carried out by an authorised technician; finally, check on the display that the temperature rises correctly during heating. The cable is 2 m long.
Easy to clean
The probe needs no special maintenance. When cleaning the baking chamber, wipe the visible sheath with a dry or slightly damp cloth, only with the oven switched off and cooled down. Do not use oven sprays or aggressive chemicals on the sheath and the cable, and do not pull on the cable.
Features and advantages of the type J thermocouple for Empero pizza ovens
✓ Original Empero part, code M.ELK-EDM-JKT-016
✓ Made by ORDEL, code OM-9/00003
✓ Type J element (iron-constantan)
✓ Stainless steel sheath and threaded fitting
✓ 2 m metal braided cable with protective spring